120回收

我也有一个变成这样了~~ 循环信息如下：
CPU clock is 792MHzDDR mode: 16 bit mode lane0+1
DDR size: 256MB
DDR check: Pass!
DDR clock: 636MHz with 2T mode
DDR pll bypass: Disabled
DDR init use : 14133 usHHH
ucl decompress...pass
0x12345678
Boot from internal device 1st NANDTE : 222667System Started
U-boot-00000-g1be8007-dirty(m8b_m201_v1@) (Apr 29 2015 - 20:36:36)clr h-ram
DRAM: 256 MiB
relocation Offset is: 0eeac000
MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
power init
out reg=c110804c,value=dfffffff
register usb cfg[0][1] = 0ff72218
register usb cfg[0][2] = 0ff72230
register usb cfg[2][0] = 0ff74ed8
NAND: Amlogic nand flash uboot driver, Version U1.06.020 (c) 2010 Amlogic Inc.
NAND BOOT : nand_init 1232
No NAND device found!!!
NAND device id: 1 f1 0 1d 1 f1
NAND device: Manufacturer ID: 0x01, Chip ID: 0x01 (AMD A revision NAND 1GiB sF1G-A)
#####aml_nand_init, none RB and chip->chip_delay:100
m3:###aml_chip->boot_oob_fill_cnt =-476
oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH8_MODE
aml_chip->oob_fill_cnt =0,aml_chip->oob_size =64,bch_bytes =14
Creating 1 MTD partitions on "nandboot":
0x000000000000-0x000000200000 : "nandboot"
nandboot initialized ok
detect mx chiprevD :0 and nand_type: 0
NAND BOOT : nand_init 1232
No NAND device found!!!
NAND device id: 1 f1 0 1d 1 f1
NAND device: Manufacturer ID: 0x01, Chip ID: 0x01 (AMD A revision NAND 1GiB sF1G-A)
1 NAND chips detected
#####aml_nand_init, none RB and chip->chip_delay:100
oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH8_MODE
aml_chip->oob_fill_cnt =0,aml_chip->oob_size =64,bch_bytes =14
multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
aml_nand_init:oobmul =1,chip->ecc.layout->oobfree[0].length=8,aml_chip->oob_size=64
aml nand env valid addr: 230000 ,status =0
mtd parttion 1 offset 4800000 changed to 300000
mtd parttion 2 offset 5800000 changed to b00000
mtd parttion 3 offset b800000 changed to 6300000
key start_blk=1016,end_blk=1023,aml_nand_key_init:684
aml nand key valid addr: 7f10000
aml nand key valid addr: 7f30000
aml nand key valid addr: 7f50000
aml nand key valid addr: 7f70000
CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
i=0,register --- nand_key
2 too much bad block!!
2 too much bad block!!
Creating 4 MTD partitions on "nandnormal":
0x000000a00000-0x000001200000 : "boot"
0x000001200000-0x000006a00000 : "upgrade"
0x000006a00000-0x000007200000 : "boot1"
0x000007200000-0x000007f00000 : "userdata"
nandnormal initialized ok
detect mx chiprevD :0 and nand_type: 0
nand_curr_device =1
NAND BOOT,nand_env_relocate_spec : env_relocate_spec 49NAND read: boot offset 0x0, size 0x1000
Enter Exception:0x00000004
link addr:0x0feb120c
QA5:A;SVN:B72;POC:3FF;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0;PASS:0;
no sdio debug board detected
TE : 24848
BT : 20:36:38 Apr 29 2015
PMU:NONE
##### VDDEE voltage = 0x041a

我的也一样，2台不同地方的，突然同时坏了

都是 不通电，网卡接头也不亮，硬盘可以转的状态

https://jingyan.baidu.com/article/ce436649132f2e3773afd3e5.html 这里好像可以救砖，我的有戏

我的也是坏了一个一代，一模一样的故障，最后卖给收宝的了

我的一代也坏了，插上电无反应，灯不亮

也收.

同一时间内都这样了？？？

同样现在，求修复方法

我的也是这几天坏的

+1

+2

+3